
20 Metre Wind V2 Extension cable
20 metre 3 wire extension cable to suit the Clipper, Target and Cruiser V2 Wind mast head units. Fitted with 3 way wire trap terminal block.

BNC / PL259 Adaptor
Adaptor to enable the BNC connector on the AIS Radar and AIS Engine to connect to the larger PL259 type VHF connector often fitted to marine VHF antenna cable.

Clipper BM-1 Battery Monitor
The BM-1 battery monitor is designed to monitor performance of 12 volt lead acid battery systems, including AGM and GEL types with capacities of up to 600 Amp hours. It is supplied complete with a precision 100 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. It also monitors the voltage of the engine start battery. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.
Fully monitors domestic battery/bank
Monitors voltage of engine start battery

Clipper BM-1 Lithium (LiFePO4) Battery Monitor
The BM-1 Li battery monitor is specifically designed for 12-Volt lithium iron
phosphate (LiFePO4) battery installation.
Capable of continuous charge or discharge currents of up to 100 Amps, BM-1 Li displays the service battery Voltage, the charge or discharge current,
the state of charge and the time to achieve full charge during charging or the time remaining during discharge.
This information leads to more efficient use of the battery, which will enhance battery life and reduce the risk of failure.

Clipper Duet with Electromagnetic 3 Log transducer
The best selling combined Speed/Distance Log and Echo Sounder in standard 110mm square size. Suitable for open cockpit mounting.
The Clipper Duet is supplied complete with the solid state electromagnetic speed transducer (for installation on most types of GRP hulls) and in hull depth transducer. Supplied with the EML-3 electromagnetic transducer, the log measures the boat speed through the water with no moving parts. Robust and accurate, the sensor generates an alternating magnetic field below the boat and measures the resulting electric field produced by the boat moving through the water. With excellent linearity and a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, the control box converts the sensor signal to a pulse output to connect to the Clipper Duet display.
Product video below. Shown with kind permission of one of our valued beta testers.

Clipper Tactical/True/Apparent Wind display
The Clipper True Wind Display shows apparent wind speed and direction, when connected to a log or GPS, it can also show true wind speed and direction.
Requires NMEA boat speed input either VHW from log or RMC from GPS for True wind speed and direction
Supply voltage nominal 12 Volts
Supply current 10mA + (10mA for back light
illumination Max)
NMEA input sentence MWV
Back light – 9 levels
Pointer style – 1
Display wind speed – 0 to 99 Kts
Display Wind angle – 0 to 360 degrees
represented by 60 segments
Display case size 110 x 110mm

Cradle mount bracket
Optional cradle mount bracket for Clipper Easy Navtex, Weatherman, AIS Plotter or Meteoman display units.

Electromagnetic Log 2 (transducer and data box)
Electromagnetic Log – speed through water – with no moving parts!
The EML-2 electromagnetic speed log measures the boat speed through the water with no moving parts.
Robust and accurate, the sensor generates an alternating magnetic field below the boat and measures the resulting electric field produced by the boat moving through the water.
With excellent linearity and a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, the control box converts the sensor signal to boat speed, trip and total distance and sends it to any compatible NMEA-0183 display.
For a complete solution the EML-2 electromagnetic transducer and controller can be supplied together with either a
or a
or to a
NMEA 2000 backbone via our converter
EML -3 is a pulse output version of the Electromagnetic Log to suit any previous NASA Marine paddlewheel log including all Target, Clipper Logs and Duet. Also works with Raymarine ST60 Log display.
Click product video below, connected to a Clipper Duet combined Depth and Log. Shown with kind permission of one of our valued beta testers.

Electromagnetic Log 3 (transducer and data box)
Electromagnetic Log – speed through water – with no moving parts! It will replace most conventional paddle wheels from all manufacturers!
The EML-3 electromagnetic speed log measures the boat speed through the water with no moving parts.
Robust and accurate, the sensor generates an alternating magnetic field below the boat and measures the resulting electric field produced by the boat moving through the water. This signal is converted to a pulse stream to replace any existing paddle wheel sensor.
With excellent linearity and a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, the control box converts the sensor signal to a pulse output to connect to any NASA Marine paddle wheel log display (Clipper Duet, Clipper Log, Target Log, Stingray Log)
Technical Info
Pulsed output to replace exsiting paddle wheel unit
Pulses per nautical mile adjustable from 15000 to 25000 PPM
Output levels – High 5V P to P
Low 0.5V P to P
(note – the transducer is a low profile unit, the 50mm OD skin fitting included
will need to be fitted in place of your current fitting)
(NOTE – NOT SUITABLE FOR METAL HULLS)
For a complete solution the EML-3 electromagnetic transducer and controller can be supplied together with a Clipper Duet
Product video below, connected to a Clipper Duet combined Depth and Log. Shown with kind permission of one of our valued beta testers.

HF Active Antenna
Active HF antenna for HF3/W and HF3/P SSB receiver. Supplied with 7 metres of cable.
Note – if your HF3 receiver has a red couloured label on the rear chassis the power supply for the antenna is already built in. It is activated by the slide switch on the rear.
If your HF3 has a black coloured label you will need the optional antenna power supply here:
http://www.nasamarine.com/product/hf-antenna-power-adaptor/

Speed log dummy impeller unit
Spare dummy log impeller
Fit this in place of the logs impeller unit if you leave the boat, this will keep the bore free from marine growth.

Supernova Mounting Bracket
Spare mounting bracket for the Supernova range of LED lights
Kit comprises of the anodised aluminium bracket, 2 x mounting blocks, 2 x M4 x 35mm stainless steel screws and 2 x M4 stainless steel Nyloc nut.

Wireless Wind Masthead Unit & Data Box
The wireless masthead transmitter outputs NMEA 0183 wind speed and direction data via its paired receiver box. It is powered by an internal battery which is charged from ambient light using a small solar panel. A few dull days will not affect performance. When fully charged, it is capable of two thousand hours of full operation in total darkness. The masthead transmitter sends data wirelessly to the base unit, which is powered by the vessel’s 12 Volt supply, the base unit receives wind speed and direction data from the masthead transmitter and sends it to a Clipper Wind display or any other compatible NMEA display unit.
- Wireless wind speed and direction data to any compatible NMEA display
- Easy installation with mast in place – no wires to run down
- Simple masthead alignment through base unit
- Light mast unit weight – 190 grams
Â

Clipper BM-2 battery monitor
The BM-2 is designed to monitor performance of 12 volt lead acid battery systems with capacities of up to 999 Amp hours. It is supplied complete with a precision 200 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.

EASY NAVTEX
Easy to read. This new navtex receiver features big, bold characters and intuitive message formatting.
Easy to program. Simple menus let you select which stations and which message categories you want to receive.
Easy on your battery. Its low power consumption and power saver mode on the backlight ensure minimum current drain.
Easy channel switching. Programmable automatic switching between the 518Khz and 490Khz channels. No more getting up early to switch channels.
Easy signal analysis. The built in spectrum analyser shows the signal in real time whilst you are receiving messages.
Easy Navtex is designed for panel mounting and is supplied with antenna, power cable and dust cover.

BM-1 Compact
Compact battery monitor, just 124 x 62mm x 23mm!
Based on the highly successful BM-1 marine battery monitor, the BM-1 Compact is especially designed for applications where space is at a premium.
Caravans, mobile homes, RV’s, small boats and renewable power installations can all benefit from the BM-1 Compact. It is able to monitor the performance of any 12 Volt lead acid battery system with a capacity up to 600 AmpHours. The BM-1 Compact is supplied with a precision 100 Amp shunt and prefabricated cables to enable simple DIY installation.
The unit continually monitors the voltage, the current (charge or discharge) and calculates the state of charge together with the time remaining to charge or discharge the battery.
This information can lead to a more efficient use of the battery enhancing its life and reducing the risk of failure.
Operation is very simple. One screen displays the voltage, current (charge or discharge) and a bar graph showing the remaining capacity. A flashing alarm is also included to warn if the capacity is getting too low. A second screen shows the remaining time available at the current charge/discharge rate together with the remaining capacity in both analog and digital format.
The BM-1 Compact consumes a miserly 1.5mA!
BM-1 Compact is used in various vehicles by the Ministry of Defence.

BM-2 Compact
The BM-2 Compact is designed for larger battery capacities and higher load currents than its BM-1 Compact sister product.
BM-2 Compact is designed especially for applications where space is at a premium. It fully monitors performance of 12 volt lead acid battery systems with capacities of up to 999 Amp hours. The package is supplied complete with a precision 200 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.

Tactical Wind Mast Sensor (NMEA 0183 Output)
A high performance system that sends NMEA wind speed and direction data 10 times a second.
In demanding conditions, where high performance is essential, the Clipper Tactical wind mast sensor is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence. Supplied as standard to Clipper, Target and Cruiser V2 wind systems.
NOTE – This 3 wire NMEA mast unit is not compatible with earlier 5 wire analogue Clipper, Target or Cruiser wind systems. The earlier analogue mast sensor is available on the spare parts page.
- Mast transmitter supplied with 20 metres of cable
- NMEA 0183 4800 Baud data sentence MWV – update rate = 10 per second
- Wind speed 0 to 99.9 Kts
- Wind direction 0 to 360 degrees
- Supply voltage nominal 12 Volts
- Wind sensor supply current 9mA

BM-1 Bluetooth Battery Monitor
BM-1 Bluetooth battery monitor BM-1 (BT) Bluetooth Battery Monitor for Android*
When you need a battery monitor but don’t have space for the display or routing the cables would be a nightmare, there is now a solution. The BM-1(BT) will monitor your boat or caravan’s lead-acid batteries and transmit the data directly to your mobile phone, or tablet, wirelessly by bluetooth.
A simple Android app, freely available from the Google Play Store, (requires Android V4.3 or later) shows your service battery voltage, current flowing in or out, state of charge and time to charge or discharge the battery. An audible alarm warns if the battery level gets dangerously low. It will also show the starter battery voltage.
For Apple users third party simple, low cost optional apps are available here IOS Battery monitor OR here IOS NASA Battery monitorÂ
The monitor, which draws a meagre 2 mA, is supplied with a 100 amp shunt and a pre-made cable assembly to simplify connection to your service battery.
Android app – Google Play Store
IOS App – App Store
NOW IN STOCK WITH YOUR DEALER
Â

MK1 Wind mast unit (5 wire) without 20M cable
Masthead unit for all MK1 Clipper, Target and Cruiser Wind systems. It is fitted with a short cable with waterproof connector to connect to your existing 20 metre long cable/connector.
OUT OF STOCK – CONTACT US – info@nasamarine.com
Â

PC Navtex USB
The PC Navtex USB is a two channel navtex receiver designed to operate on your personal computer. It will receive navtex messages even without your PC connected. Navtex messages are stored in a vast internal memory for you to download when you get on board. Down loading is quick and the software provided allows you to select the messages you want.
Leave the unit on 24/7 then, when you get on board, just plug in your PC and immediately download the latest weather forecast from your local station, or any other message stored in the PC Navtex USB’s memory.
An excellent website with details of NAVTEX, RTTY and HF radio weather services can be found here:Â http://weather.mailasail.com/Franks-Weather
Try the PC Navtex software before you buy – download a full working version here: PC Navtex Demo (requires PC Windows XP – 10)
Latest production PC Navtex software V4 (Windows 10 Compatible) – http://www.willrite.co.uk/Navtex/Downloads/navtex4_installer.exe

BM-1/Compact/BM-2 spare 5 metre cable
5 metre cable for BM-1, BM-2 or BM Compact battery Monitors

H Vector Navtex Antenna
Conventional navtex antennas respond to the electrical component associated with the navtex radio signal. They usually perform well at sea where electrical interference is low but can sometimes be overwhelmed with interference especially when in harbour and connected to shore power.
In most small craft the electrical system acts as an effective ground for the antenna but it can also be a source of interference conducted from other electrical equipment on board. Electrical interference can result in poor reception especially in a marina where the ambient level is high or at sea when poorly suppressed electrical equipment is in use.
The omnidirectional H-Vector antenna is not sensitive to electric fields but to the magnetic component of the navtex signal. As a result it is less sensitive to locally generated interference and, as it does not need a ground, it is not affected by conducted ground interference whether in harbour or at sea.
The net result is that, under adverse conditions, the H-Vector antenna can deliver a significant improvement to navtex reception. The mushroom shaped antenna is compatible with the Clipper navtex, series 2 Target navtex and with the navtex engine. It can be mounted on a cabin roof or rail mounted using an appropriate threaded antenna base.
Customer review:
I am delighted with our new antenna. Our Navtex , normally somnolent in the marina, has burst into life!
Someone asked me recently – why bother with Navtex? My answer was simple. Last year a gale blew up suddenly on the Turkish Aegean coast. The Navtex transmitter at Izmir issued an urgent gale warning out of ‘normal hours’ and it was the only service to do so! For example there was nothing about this gale on PredictWind on our WiFi.
Now had a full month on the boat in Turkey cruising around and am even more delighted than ever with the new antenna!
John E – cruising in Turkey

HF3 Panel Mount Kit
Panel mount kit for HF3/W and HF3/P receivers,
supplied with external speaker

Series 2 Navtex Antenna
Spare antenna complete with 7 metre cable – suitable for Clipper Navtex and Target Navtex 2 channel receivers
(Not suitable for single frequency receivers – see 518Khz type)

Target Navtex Pro-Plus V2
The Target Navtex Pro is packed with features yet is still remarkably easy to install and use. Great care has been taken to make this unit very simple to operate, in fact should one lose the comprehensive instruction book supplied with it, it is possible to program the unit via the on-screen menus – it really is that simple. The messages are displayed on a high contrast backlit liquid crystal display with a clear line space between messages to aid location – this is necessary as the unit has a very large memory.
You can be sure you always have up to the minute data as the memory will overwrite the oldest messages if it becomes full. However you can at any time erase the data memory if you wish. It is like a continuous stream of paper – without the mess or expense!
Navtex has come of age, a free worldwide information service in English. A Navtex receiver is a most essential piece of equipment and the Target Navtex Pro is state of the art. This excellent piece of equipment comes complete with its own active aerial and is designed to be left on continuously – consuming a miserly 40mA. Can you afford to be without one?
An excellent website with details of NAVTEX, RTTY and HF radio weather services can be found here: http://weather.mailasail.com/Franks-Weather
The Target Navtex receiver is supplied with – Antenna and 7 metre cable, a power cable, a crade mount bracket and a manual.

MK1 Mast Head Unit (5 wire) with 20M cable
Compatible with MK1 Clipper, Cruiser and Target Wind instruments with 5 wires.
Complete masthead unit with 20 metres of cable and mounting brackets
OUT OF STOCK – CONTACT US – info@nasamarine.com
Â

BT-3 Bluetooth Navtex receiver
The new bluetooth Navtex is a dual frequency Navtex receiver that decodes and stores Navtex messages for viewing on an Android bluetooth enabled mobile phone or tablet. The unit is designed to be run continuously and have the stored messages downloaded as and when required by the user. An android app enables the user to search the stored messages or to program the device to display only wanted message types from selected stations.
The internal memory stores in excess of four hundred typical Navtex messages with new messages overwriting the oldest. The receiver can be supplied with a standard E-vector antenna or, for more challenging conditions, an H-vector antenna is also available. The H-vector antenna has a standard 14 tpi mount and is connected to the receiver using the seven metre cable provided. It can be either surface of rail mounted and there are several suitable, optional mounts available. A fused power cable is also supplied to connect the receiver to a permanent 12 volt power source.
The android app can be freely downloaded from the google play store
(Other Android options are available from the developer at www.willrite.co.uk/GS/GS_products.html)
For Apple users there are third party cost optional IOS apps available:
NASA Navtex BTLE Â Â Note – Latest update supports Dark Mode
or
Recommended mimimum iphone requirement 6s upwards and IOS 12
BT-3 Navtex with Series 2 Antenna £161.26 inc VAT
BT-3 Navtex with H Vector Antenna £180.60 inc VAT

Spare alarm buzzer – Clipper, Target and Cruiser Depth
Spare alarm buzzer for the Clipper, Target, Cruiser Depth sounders and AIS Radar/Plotter.

Through hull transducer mount kit
Kit for mounting the depth transducer through wooden or steel hulls.
L = 185mm, W = 82mm, H = 40mm
AIS Plotter utility cable
AIS Plotter spare cable to connect the AIS to GPS NMEA source

Clipper Electromagnetic 2 Speed Log
The Clipper electromagnetic speed log measures the boat speed through the water with no moving parts.
Robust and accurate, the sensor generates an alternating magnetic field below the boat and measures the resulting electric field produced by the boat moving through the water. It is designed for installation into most types of GRP hulls.
With excellent linearity and a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, the log sensor sends signals to a control box which then converts the sensor signal to boat speed, trip and total distance. This data is transmitted in NMEA 0183 format to a Clipper EM Log display unit.
(NOTE – NOT SUITABLE FOR METAL HULLS)

Clipper Electromagnetic Speed Log Display
The new Clipper EM Log display unit connects directly to the EM Log 2 control box to display boat speed through the water with no moving parts.
Multiple displays can be connected to the EM Log 2 control box.
The speed is displayed with a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, it also shows trip and total distance.
Â
Â

Target Electromagnetic Speed Log
The Target electromagnetic speed log measures the boat speed through the water with no moving parts.
Robust and accurate, the sensor generates an alternating magnetic field below the boat and measures the resulting electric field produced by the boat moving through the water. It is designed for installation into most types of GRP hulls.
With excellent linearity and a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, the log sensor sends signals to a control box which then converts the sensor signal to boat speed, trip and total distance. This data is transmitted in NMEA 0183 format to a new Target EM Log display unit.
IN STOCK

Clipper Wind Master Display MK1 5 WIRE
Spare Clipper Wind master display unit complete with weather cover
This connects to the 5 wire analogue output mast head unit.

5M Extension cable
5 metre long extension cable (5 way) for early type 5 wire wind masthead unit or for extending the Clipper Depth Repeater cable.
(Note this cable suits the early type masthead units without the masthead connectors,
if it is to be used with later type masthead units removal of the plug and socket is required)
(Note this is not suitable with the later version 3 wire wind mast head units.)

Target Electromagnetic Speed Log display unit
The Target Electromagnetic Log display unit connects directly to the NMEA 0183 output of the electromagnetic speed transducer.
Supplied with 5 metre cable, fixing bracket and weather cover.

Dust cover
Dust cover for Clipper Navtex, Weatherman, AIS Radar,
Meteoman and MOBi man overboard indicator.1

Instrument O ring
Spare ‘O’ ring to seal instrument displays to panel.
Select the type required from the drop down menu.
Select:
Clipper cockpit for Clipper Depth, Log, Wind, Compass, Duet, Easylog, BM-1/2 and GPS Repeater etc.
Clipper cabin for Clipper Navtex, AIS Plotter, Weatherman, Meteoman Barometer and Mobi man overboard indicator
Target for Target Depth, Log, Wind and Compass
Cruiser for Cruiser Depth, Log, Wind and Compass

HF Antenna power adaptor
HF3 has the power supply for the HF antenna built in since 2005 (Red label on back of radio chassis).
If you want to use the antenna for another receiver you will need this power adaptor to provide 12V.

518Khz navtex antenna
Spare 518kHz antenna for older single channel Target navtex. Complete with 7 metre cable.

Weatherman antenna (with 7 metre cable) included with weatherman
Spare antenna with 7 metre cable

Clipper Log master display
Replacement Clipper Log master display unit
Technical Specifications
- 40mm high digits
- Speed (Knots/m.p.h.)
- Trip Distance (N.Miles / Miles)
- Total Distance (N.Miles / Miles)
- Trend indicator shows acceleration / deceleration
- Selectable speed averaging
- Tactile keypad
- NMEA 0183 output VHW & VLW
- Consumption 10mA + 10mA for display backlight

Clipper Wind (MK 1) NMEA output connector (25cm)
Din connector and short cable with wire trap terminal block (25cm)
This connects to the MK1 five wire Clipper Wind display output socket to enable NMEA output to other devices.
Also suitable for NMEA input to the Meteoman Barometer

Clipper Wind NMEA Output cable (5 metre for MK1 five wire masthead systems)
This cable connects to the back of the MK1 five wire Clipper Wind display to enable the NMEA output to be connected to external devices. Cable length 5 metres Fitted with 2 way wire trap terminal block

NMEA Extension Cable 5 metre
3 way – 5 metre extension cable for NMEA products
Eg – for adding a 5 metre extension to Clipper Wind V2 display