Tactical Wind Mast Sensor (NMEA)
A high performance system that sends NMEA wind speed and direction data 10 times a second.
In demanding conditions, where high performance is essential, the Clipper Tactical wind mast sensor is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence. Supplied as standard to Clipper, Target and Cruiser V2 wind systems.
NOTE – This 3 wire NMEA mast unit is not compatible with earlier 5 wire analogue Clipper, Target or Cruiser wind systems. The earlier analogue mast sensor is available on the spare parts page.
- Mast transmitter supplied with 20 metres of cable
- NMEA 0183 4800 Baud data sentence MWV – update rate = 10 per second
- Wind speed 0 to 99.9 Kts
- Wind direction 0 to 360 degrees
- Supply voltage nominal 12 Volts
- Wind sensor supply current 9mA
You may also like...
Supernova Combi Tri and Anchor L.E.D mastlight
Supernova lights use high efficiency LEDs ensuring long life and low power consumption. A tough polycarbonate shell protects Supernova from the elements while a Gore-Tex membrane vent ensures equalization of pressure on the seals.
A simple two wire connection powers the Combi light. Connecting the red wire to positive and the black wire to negative will illuminate the tricolour light. Reversing the connections will illuminate the anchor light.
A pre-wired toggle switch is supplied with the Combi light to facilitate the supply reversal.
In the central position both lights are off. Switching left or right selects the required lighting configuration.
Supernova navigation lights are intended for use on vessels up to 12 metres in length. They comply with CE generic EMC standards and are waterproof to IP65 and IP67. There is no specific EU standard for LED navigation lights. Supernova lights do not have any national approvals.
Supplied with pre wired switch and mounting bracket.
EX-1 exhaust temperature monitor/alarm
The EX-1 continually displays the exhaust gas temperature in wet exhaust systems giving advanced warning of potential problems.
The EX-1 measures the exhaust gas temperature directly and displays it in degrees centigrade or Fahrenheit. Once the normal working temperature has been established a maximum temperature, a few degrees higher, can be programmed into the EX-1 which will then sound an alarm if that temperature is exceeded.Even a small rise in temperature can indicate a potential problem such as a minor blockage, leak or failing pump which can be corrected before a complete failure occurs.
I just wanted to share with you another great reason for having the EX-1 fitted. Over the last few weeks of using our boat I observed that the running temperature had gone up around 5 degrees or so. Now with using the boat in the winter one would expect the reverse, so it caused me to think more about it. Added to that, when I did use the engine at full revs on load (something I do regularly just as a check) the exhaust alarm went off (it doesn’t normally.) I then observed the seawater tell-tail was more pronounced (the tell-tail feed is off the line between the Jabsco pump and the inlet to the cooler. Hmmm: possible blockage? I removed the impellor and true enough, one of the vanes had come off. On stripping the cooling system (I was already working on the leaking silencer) I found one part of the impellor up against the tube stack, but more importantly, when I removed the hose feeding the tube stack, via a small elbow, I found a larger part of the impellor jammed inside, reducing the flow by as much as 50% and causing s sediment build up behind it, reducing it further. All cleaned out now, but the reason for telling you is that the EX-1 gave me warning before any real damage could have been caused. It is a brilliant piece of kit.
Compact battery monitor, just 124 x 62mm x 23mm!
Based on the highly successful BM-1 marine battery monitor, the BM-1 Compact is especially designed for applications where space is at a premium.
Caravans, mobile homes, RV’s, small boats and renewable power installations can all benefit from the BM-1 Compact. It is able to monitor the performance of any 12 Volt lead acid battery system with a capacity up to 600 AmpHours. The BM-1 Compact is supplied with a precision 100 Amp shunt and prefabricated cables to enable simple DIY installation.
The unit continually monitors the voltage, the current (charge or discharge) and calculates the state of charge together with the time remaining to charge or discharge the battery.
This information can lead to a more efficient use of the battery enhancing its life and reducing the risk of failure.
Operation is very simple. One screen displays the voltage, current (charge or discharge) and a bar graph showing the remaining capacity. A flashing alarm is also included to warn if the capacity is getting too low. A second screen shows the remaining time available at the current charge/discharge rate together with the remaining capacity in both analog and digital format.
The BM-1 Compact consumes a miserly 1.5mA!
BM-1 Compact is used in various vehicles by the Ministry of Defence.
AIS Engine 3 upgrade processor
The AIS Engine 1 and 2 can be upgraded to AIS Engine 3 specification by replacing the processor. This is a straightforward procedure where the old device is simply unplugged from its socket and replaced by the new device. AIS Engine 3 relays all AIS messages.
20W Semi Flexible SOLAR PANEL
At just 3.5mm thin our weather proof panels are tough enough to withstand being stepped on when wearing soft soled shoes
A solar panel can provide a near maintenance free solution to keeping batteries charged when unattended. An occasional wipe with a damp cloth is all that is necessary to ensure the panel continues to trickle energy into the battery. Keeping the battery topped up will improve its reliability and can extend its useful working life. Whilst solar panels give their maximum output in direct sunlight, even an overcast day can provide a useful level of charge.
The Nasa Marine 12 volt, semi flexible solar panel is robustly constructed on a fibre glass substrate and are protected by a scratch proof transparent Tedlar polymer. Only 3.5mm thick and lightweight, they have no metal outer components to make contact with the surface to which they are fitted. The efficient and stable polycrystalline cells are encapsulated between two tough outer layers so the whole panel is weatherproof and carries a limited one year warranty.
The panel can be gently flexed (in one dimension.) to follow a smooth curve, such as a coach roof, by up to 2.5cm per 100cm of panel length. Four, grommet finished, holes are provided for screw fixing. Alternatively panels can be glued into position using mastic. The panels do not contain glass and, when correctly mounted, can be stepped upon when wearing soft soled shoes.
A sealed junction box is fitted with 2.5m of output cable, a connector and fuse protected crocodile clips. Electrical connection is simple though the use of a solar regulator is recommended to prevent overcharge if the system is to be left unattended for long periods or the solar panel to battery ratio exceeds the minimum of 10W to 100Ah. An internal blocking diode prevents reverse current drain at night. The panel is protected with an inline 3 Amp fuse.
The 20W panel measures 510 x 360mm
A large display, mast mounted, multifunction repeater is now being produced at our factory. The weatherproof repeater with its 60mm high numerals, is supplied complete with cables, data-box with six NMEA-0183 inputs ( With up to six sentences per input.), wireless remote control, stainless steel mounting brackets and weather cover. There are nine levels of red back lighting which permit easy night viewing of red characters on a black background. The overall case size is 211mm wide x 140mm high.
Currently programmed in are the screens shown below though we do welcome customer feedback as we will add to this list by popular demand.