Clipper Wind (MK 1) NMEA output connector (25cm)
£6.46
Din connector and short cable with wire trap terminal block (25cm)
This connects to the MK1 five wire Clipper Wind display output socket to enable NMEA output to other devices.
Also suitable for NMEA input to the Meteoman Barometer
You may also like...

RG 58 10 m Cable pack
Coaxial cables are vital to the performance of your antenna and radio system. Selecting the best coaxial cable has become more and more complicated as more suppliers are offering a broader range of products. The cable selected will affect the system’s cost, coverage and reliability. That’s why for our antennas we only use one type of coaxial cable, the TOP PERFORMANCE RG 58 CU MIL, designed to guarantee the best signal transmission.

Meteoman masthead Unit *
Masthead unit for connection to the Meteoman Barometer.
The unit sends apparent wind speed and direction data via NMEA 0183 to Meteoman display. Complete with 20 metres of cable.

5M Extension cable
5 metre long extension cable (5 way) for early type 5 wire wind masthead unit or for extending the Clipper Depth Repeater cable.
(Note this cable suits the early type masthead units without the masthead connectors,
if it is to be used with later type masthead units removal of the plug and socket is required)
(Note this is not suitable with the later version 3 wire wind mast head units.)

AIS Engine 3 upgrade processor
The AIS Engine 1 and 2 can be upgraded to AIS Engine 3 specification by replacing the processor. This is a straightforward procedure where the old device is simply unplugged from its socket and replaced by the new device. AIS Engine 3 relays all AIS messages.

Wireless Wind Masthead Unit & Data Box
The wireless masthead transmitter outputs NMEA 0183 wind speed and direction data via its paired receiver box. It is powered by an internal battery which is charged from ambient light using a small solar panel. A few dull days will not affect performance. When fully charged, it is capable of two thousand hours of full operation in total darkness. The masthead transmitter sends data wirelessly to the base unit, which is powered by the vessel’s 12 Volt supply, the base unit receives wind speed and direction data from the masthead transmitter and sends it to a Clipper Wind display or any other compatible NMEA display unit.
- Wireless wind speed and direction data to any compatible NMEA display
- Easy installation with mast in place – no wires to run down
- Simple masthead alignment through base unit
- Light mast unit weight – 190 grams

Tactical Wind Mast Sensor (NMEA 0183 Output)
A high performance system that sends NMEA wind speed and direction data 10 times a second.
In demanding conditions, where high performance is essential, the Clipper Tactical wind mast sensor is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence. Supplied as standard to Clipper, Target and Cruiser V2 wind systems.
NOTE – This 3 wire NMEA mast unit is not compatible with earlier 5 wire analogue Clipper, Target or Cruiser wind systems. The earlier analogue mast sensor is available on the spare parts page.
- Mast transmitter supplied with 20 metres of cable
- NMEA 0183 4800 Baud data sentence MWV – update rate = 10 per second
- Wind speed 0 to 99.9 Kts
- Wind direction 0 to 360 degrees
- Supply voltage nominal 12 Volts
- Wind sensor supply current 9mA

Dust cover
Dust cover for Clipper Navtex, Weatherman, AIS Radar,
Meteoman and MOBi man overboard indicator.1