Technical Specifications
- Deep and shallow alarms (audible and visual)
- Consumption 10mA + 25Ma for backlight (max)
- 7 level display backlighting
- Complete with 5 metre cable, ‘O’ ring and weather cover
£86.10
The Clipper Depth Repeater has its own independent alarm function as well as repeating all data from the master unit.
Note – this is not a stand alone unit and cannot be connected to a depth transducer.
It must be connecetd to the Clipper Depth master display unit.
Technical Specifications
The Clipper wireless wind is supplied with a wireless masthead transmitter, a base unit and a Clipper Wind display unit. The wireless masthead transmitter is powered by an internal battery which is charged from ambient light using a small solar panel. A few dull days will not affect performance. When fully charged, it is capable of two thousand hours of full operation in total darkness. The masthead transmitter sends data wirelessly to the base unit, which is powered by the vessel’s 12 Volt supply, the base unit receives wind speed and direction data from the masthead transmitter and sends it to the Clipper Wind display or any other compatible NMEA display unit.
The Clipper Wind display is in the industry standard 110mm square case. Exceptionally large and clear display with 60 segments for full 360 degree direction indication.
EASY LOG – the Log with no moving parts
The Clipper EASY LOG shows speed, trip and total distance on a high visibility liquid crystal display. It utilises the RMC sentence from any GPS or plotter with an NMEA 0183 output. Alternatively the EASY LOG can repeat, using sentences VHW and VLW from an existing NMEA log.
The Clipper GPS repeater has quickly established itself as the market leader in cockpit GPS repeaters. Typical of the Clipper range it boasts large clear digits and simple operation. Installation coundn’t be simpler with just a single wing nut to fasten the unit into the panel and two wires to connect to the GPS.
This connects directly to the master wind unit. As well as repeating the wind speed it shows wind direction in high resolution when sailing close to – or running with the wind. Complete with 5M cable.
A high performance instrument system that shows almost instantaneous changes of wind speed and direction.
In demanding conditions, where high performance is essential, the Clipper Tactical wind system is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence.
The BM-1 battery monitor is designed to monitor performance of 12 volt lead acid battery systems, including AGM and GEL types with capacities of up to 600 Amp hours. It is supplied complete with a precision 100 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. It also monitors the voltage of the engine start battery. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.
Fully monitors domestic battery/bank
Monitors voltage of engine start battery
The Clipper True Wind Display shows apparent wind speed and direction, when connected to a log or GPS, it can also show true wind speed and direction.
Requires NMEA boat speed input either VHW from log or RMC from GPS for True wind speed and direction
Supply voltage nominal 12 Volts
Supply current 10mA + (10mA for back light
illumination Max)
NMEA input sentence MWV
Back light – 9 levels
Pointer style – 2
Display wind speed – 0 to 99 Kts
Display Wind angle – 0 to 360 degrees
represented by 60 segments
Display case size 110 x 110mm
The Clipper Wind NMEA Repeater has user a selectable pointer style and selectable wind speed scale. It requires the standard NMEA 0183 MWV data sentence.
(Supplied as standard equipment to the Clipper Wind V2 – 3 wire wind mast unit and the Clipper Wireless wind unit.)