5M Extension cable
£18.62
5 metre long extension cable (5 way) for early type 5 wire wind masthead unit or for extending the Clipper Depth Repeater cable.
(Note this cable suits the early type masthead units without the masthead connectors,
if it is to be used with later type masthead units removal of the plug and socket is required)
(Note this is not suitable with the later version 3 wire wind mast head units.)
You may also like...
AIS RADAR SART UPGRADE CHIP
This ‘do it yourself’ install chip will enhance your AIS Radar by adding the latest SART function. If a SART (search and rescue transponder) transmission is received the AIS Radar will sound an alarm in the SOS tone. The zoom range is also enhanced by zooming right down to 0.125 nautical miles for easier location of the SART beacon/MOB. Additionally a course over ground pointer can be activated by the user which appears if your vessel is moving at 2 knots or more, this greatly simplifies the interpretation of targets on the screen relative to your own boats heading.
Clipper Wind Master Display MK1 5 WIRE
Spare Clipper Wind master display unit complete with weather cover
This connects to the 5 wire analogue output mast head unit.
Waterproof VHF Extension Speaker
Popular 5 watt waterproof extension speaker fits most VHF’s
BNC / PL259 Adaptor
Adaptor to enable the BNC connector on the AIS Radar and AIS Engine to connect to the larger PL259 type VHF connector often fitted to marine VHF antenna cable.
PL259 nickel plated male connector
High quality male connector, nickel plated with silver tip and teflon insulator. For coaxial cable RG 58.
Tactical Wind Mast Sensor (NMEA 0183 Output)
A high performance system that sends NMEA wind speed and direction data 10 times a second.
In demanding conditions, where high performance is essential, the Clipper Tactical wind mast sensor is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence. Supplied as standard to Clipper, Target and Cruiser V2 wind systems.
NOTE – This 3 wire NMEA mast unit is not compatible with earlier 5 wire analogue Clipper, Target or Cruiser wind systems. The earlier analogue mast sensor is available on the spare parts page.
- Mast transmitter supplied with 20 metres of cable
- NMEA 0183 4800 Baud data sentence MWV – update rate = 10 per second
- Wind speed 0 to 99.9 Kts
- Wind direction 0 to 360 degrees
- Supply voltage nominal 12 Volts
- Wind sensor supply current 9mA
AIS Engine 3 upgrade processor
The AIS Engine 1 and 2 can be upgraded to AIS Engine 3 specification by replacing the processor. This is a straightforward procedure where the old device is simply unplugged from its socket and replaced by the new device. AIS Engine 3 relays all AIS messages.
Clipper Tactical/True/Apparent Wind display
The Clipper True Wind Display shows apparent wind speed and direction, when connected to a log or GPS, it can also show true wind speed and direction.
Requires NMEA boat speed input either VHW from log or RMC from GPS for True wind speed and direction
Supply voltage nominal 12 Volts
Supply current 10mA + (10mA for back light
illumination Max)
NMEA input sentence MWV
Back light – 9 levels
Pointer style – 1
Display wind speed – 0 to 99 Kts
Display Wind angle – 0 to 360 degrees
represented by 60 segments
Display case size 110 x 110mm
