20 Metre Wind V2 Extension cable
£23.64
20 metre 3 wire extension cable to suit the Clipper, Target and Cruiser V2 Wind mast head units. Fitted with 3 way wire trap terminal block.
Accessories and Spare Parts

Target Wind Speed & Direction V2
All instruments in the Target Range come complete with sensors or transducers as appropriate and all necessary fittings. They are designed to run on 12v supply, but due to the very low power consumption there is no reason why they cannot run off dry batteries. They provides accurate readings for owners of sailing craft and powerboats alike.
Designed for long term maintenance-free performance, the Target Wind Speed and Direction instrument is robust in manufacture and simple in operation. Initial set-up aligns the boats head with the wind indicator, so the masthead unit can be mounted in any convenient location and is not bound to fore-aft mounting.

Clipper Wind System V2
The Clipper Wind system shares the same 110mm square case as its sister instruments in the Clipper range. the display is exceptionally large and clear, with 60 segments for full 360 degree direction indication. Windspeed is shown in knots, M.P.H. or Metres/second. The pointer style is selectable, from the single segment shown above, to multi segments for greater clarity or a ‘windex’ style indicator. The new masthead unit has NMEA 0183 output sentence MWV and supplied with 20 metres of cable.
Clipper Wind system is supplied complete with Display unit, masthead unit with cable and mounting blocks.
You may also like...

HF3 Panel Mount Kit
Panel mount kit for HF3/W and HF3/P receivers,
supplied with external speaker

H Vector Navtex Antenna
Conventional navtex antennas respond to the electrical component associated with the navtex radio signal. They usually perform well at sea where electrical interference is low but can sometimes be overwhelmed with interference especially when in harbour and connected to shore power.
In most small craft the electrical system acts as an effective ground for the antenna but it can also be a source of interference conducted from other electrical equipment on board. Electrical interference can result in poor reception especially in a marina where the ambient level is high or at sea when poorly suppressed electrical equipment is in use.
The omnidirectional H-Vector antenna is not sensitive to electric fields but to the magnetic component of the navtex signal. As a result it is less sensitive to locally generated interference and, as it does not need a ground, it is not affected by conducted ground interference whether in harbour or at sea.
The net result is that, under adverse conditions, the H-Vector antenna can deliver a significant improvement to navtex reception. The mushroom shaped antenna is compatible with the Clipper navtex, series 2 Target navtex and with the navtex engine. It can be mounted on a cabin roof or rail mounted using an appropriate threaded antenna base.
Customer review:
I am delighted with our new antenna. Our Navtex , normally somnolent in the marina, has burst into life!
Someone asked me recently – why bother with Navtex? My answer was simple. Last year a gale blew up suddenly on the Turkish Aegean coast. The Navtex transmitter at Izmir issued an urgent gale warning out of ‘normal hours’ and it was the only service to do so! For example there was nothing about this gale on PredictWind on our WiFi.
Now had a full month on the boat in Turkey cruising around and am even more delighted than ever with the new antenna!
John E – cruising in Turkey

NMEA Compass Sensor
Compact and waterproof NMEA compass sensor transmits NMEA 0183 sentence HDG to Clipper, Target and Cruiser or other equipment.

HF Active Antenna
Active HF antenna for HF3/W and HF3/P SSB receiver. Supplied with 7 metres of cable.
Note – if your HF3 receiver has a red couloured label on the rear chassis the power supply for the antenna is already built in. It is activated by the slide switch on the rear.
If your HF3 has a black coloured label you will need the optional antenna power supply here:
http://www.nasamarine.com/product/hf-antenna-power-adaptor/

Clipper Tactical/True/Apparent Wind display
The Clipper True Wind Display shows apparent wind speed and direction, when connected to a log or GPS, it can also show true wind speed and direction.
Requires NMEA boat speed input either VHW from log or RMC from GPS for True wind speed and direction
Supply voltage nominal 12 Volts
Supply current 10mA + (10mA for back light
illumination Max)
NMEA input sentence MWV
Back light – 9 levels
Pointer style – 1
Display wind speed – 0 to 99 Kts
Display Wind angle – 0 to 360 degrees
represented by 60 segments
Display case size 110 x 110mm

Waterproof VHF Extension Speaker
Popular 5 watt waterproof extension speaker fits most VHF’s

Cradle mount bracket
Optional cradle mount bracket for Clipper Easy Navtex, Weatherman, AIS Plotter or Meteoman display units.