Clipper BM-1 Battery Monitor
The BM-1 battery monitor is designed to monitor performance of 12 volt lead acid battery systems, including AGM and GEL types with capacities of up to 600 Amp hours. It is supplied complete with a precision 100 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. It also monitors the voltage of the engine start battery. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.
Fully monitors domestic battery/bank
Monitors voltage of engine start battery
Clipper Tactical/True/Apparent Wind display
The Clipper True Wind Display shows apparent wind speed and direction, when connected to a log or GPS, it can also show true wind speed and direction.
Requires NMEA boat speed input either VHW from log or RMC from GPS for True wind speed and direction
Supply voltage nominal 12 Volts
Supply current 10mA + (10mA for back light
NMEA input sentence MWV
Back light – 9 levels
Pointer style – 2
Display wind speed – 0 to 99 Kts
Display Wind angle – 0 to 360 degrees
represented by 60 segments
Display case size 110 x 110mm
Clipper BM-2 battery monitor
The BM-2 is designed to monitor performance of 12 volt lead acid battery systems with capacities of up to 999 Amp hours. It is supplied complete with a precision 200 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.
Clipper Electromagnetic Speed Log
The new Clipper electromagnetic speed log measures the boat speed through the water with no moving parts.
Robust and accurate, the sensor generates an alternating magnetic field below the boat and measures the resulting electric field produced by the boat moving through the water. It is designed for installation into most types of GRP hulls.
With excellent linearity and a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, the log sensor sends signals to a control box which then converts the sensor signal to boat speed, trip and total distance. This data is transmitted in NMEA 0183 format to a new Clipper EM Log display unit.
Clipper Electromagnetic Speed Log Display
The new Clipper EM Log display unit connects directly to the EM Log control box to display boat speed through the water with no moving parts.
The speed is displayed with a resolution of 0.1 Knot, over the range 0.2 to 40 Knots, it also shows trip and total distance.
IN PRODUCTION – ORDER WITH YOUR DEALER
Clipper Tactical Wind System
A high performance instrument system that shows almost instantaneous changes of wind speed and direction.
In demanding conditions, where high performance is essential, the Clipper Tactical wind system is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence.
Clipper Depth Repeater
The Clipper Depth Repeater has its own independent alarm function as well as repeating all data from the master unit.
Note – this is not a stand alone unit and cannot be connected to a depth transducer.
It must be connecetd to the Clipper Depth master display unit.
Clipper Wind Repeater/V2 – 3 wire mast unit display
The Clipper Wind NMEA Repeater has user a selectable pointer style and selectable wind speed scale. It requires the standard NMEA 0183 MWV data sentence.
(Supplied as standard equipment to the Clipper Wind V2 – 3 wire wind mast unit and the Clipper Wireless wind unit.)
Clipper GPS Repeater
The Clipper GPS repeater has quickly established itself as the market leader in cockpit GPS repeaters. Typical of the Clipper range it boasts large clear digits and simple operation. Installation coundn’t be simpler with just a single wing nut to fasten the unit into the panel and two wires to connect to the GPS.
Clipper Wind System V2
The Clipper Wind system shares the same 110mm square case as its sister instruments in the Clipper range. the display is exceptionally large and clear, with 60 segments for full 360 degree direction indication. Windspeed is shown in knots, M.P.H. or Metres/second. The pointer style is selectable, from the single segment shown above, to multi segments for greater clarity or a ‘windex’ style indicator. The new masthead unit has NMEA 0183 output sentence MWV and supplied with 20 metres of cable.
Clipper Wind system is supplied complete with Display unit, masthead unit with cable and mounting blocks.
Clipper Compass System
The Clipper Compass is a fully electronic compass with remote fluxgate sensor. The large clear display has 7 levels of illumination and gives True or magnetic heading. The sensor which is gimballed for plus/minus 30 degrees of pitch and roll, is mounted in a position where stray magnetic fields are at a minimum. An electronic auto calibration then cancels out small errors.
Steer to course function
When the steering function is selected a series of chevrons accumulate showing the magnitude and direction of the steering error. To stay on course simply turn the wheel in the direction of the chevrons until they are extinguished. The steering sensitivity can be preset by the user. An off course alarm provides a safety feature when not at the helm. If the heading deviates by more than a preset amount then the alarm will sound.
Clipper Speed & Distance System
Well proven paddle wheel speed and distance log with giant digits for easy viewing.
The Clipper Log is supplied with a through hull paddle wheel unit with 7 metres of cable – designed for installation on most GRP type hulls, Clipper display unit, weather cover and blanking cap.
Clipper Depth System
Best selling Depth sounder with giant 40mm high digits for easy viewing. The outstanding Clipper range of instruments incorporate technically advanced electronics in an industry standard 110mm square case. Supplied complete with in hull depth transducer with 7 metre cable.
Clipper Duet System
Best selling combined Speed/Distance Log and Echo Sounder in standard 110mm square size. Suitable for open cockpit mounting.
The Clipper Duet is supplied complete with paddlewheel transducer (for installation on most types of GRP hulls) and in hull depth transducer.
Clipper Wireless Wind (Aparrent)
The Clipper wireless wind is supplied with a wireless masthead transmitter, a base unit and a Clipper Wind display unit. The wireless masthead transmitter is powered by an internal battery which is charged from ambient light using a small solar panel. A few dull days will not affect performance. When fully charged, it is capable of two thousand hours of full operation in total darkness. The masthead transmitter sends data wirelessly to the base unit, which is powered by the vessel’s 12 Volt supply, the base unit receives wind speed and direction data from the masthead transmitter and sends it to the Clipper Wind display or any other compatible NMEA display unit.
The Clipper Wind display is in the industry standard 110mm square case. Exceptionally large and clear display with 60 segments for full 360 degree direction indication.
- Wireless wind speed and direction data to any compatible NMEA display
- Easy installation with mast in place – no wires to run down
- Simple masthead alignment through base unit
- Light mast unit weight – 190 grams
Clipper Easy log
EASY LOG – the Log with no moving parts
The Clipper EASY LOG shows speed, trip and total distance on a high visibility liquid crystal display. It utilises the RMC sentence from any GPS or plotter with an NMEA 0183 output. Alternatively the EASY LOG can repeat, using sentences VHW and VLW from an existing NMEA log.