
BM-1 Compact
Compact battery monitor, just 124 x 62mm x 23mm!
Based on the highly successful BM-1 marine battery monitor, the BM-1 Compact is especially designed for applications where space is at a premium.
Caravans, mobile homes, RV’s, small boats and renewable power installations can all benefit from the BM-1 Compact. It is able to monitor the performance of any 12 Volt lead acid battery system with a capacity up to 600 AmpHours. The BM-1 Compact is supplied with a precision 100 Amp shunt and prefabricated cables to enable simple DIY installation.
The unit continually monitors the voltage, the current (charge or discharge) and calculates the state of charge together with the time remaining to charge or discharge the battery.
This information can lead to a more efficient use of the battery enhancing its life and reducing the risk of failure.
Operation is very simple. One screen displays the voltage, current (charge or discharge) and a bar graph showing the remaining capacity. A flashing alarm is also included to warn if the capacity is getting too low. A second screen shows the remaining time available at the current charge/discharge rate together with the remaining capacity in both analog and digital format.
The BM-1 Compact consumes a miserly 1.5mA!
BM-1 Compact is used in various vehicles by the Ministry of Defence.

BM-2 Compact
The BM-2 Compact is designed for larger battery capacities and higher load currents than its BM-1 Compact sister product.
BM-2 Compact is designed especially for applications where space is at a premium. It fully monitors performance of 12 volt lead acid battery systems with capacities of up to 999 Amp hours. The package is supplied complete with a precision 200 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure.

EASY LIGHT LED Luminaire
The NASA Marine 12 Volt Easylight luminaire contains 48 high efficiency LEDs in a slender surface mounting package.
The cool white version (CW) is recommended where maximum illumination is required and the warm white (WW) where a more natural light is preferred. Light output for the (CW) is typically 300 Lumens and typically 250 Lumens for the (WW).
The unit is designed for surface mounting directly on a ceiling or wall using the screws provided. It is not waterproof and is intended for use in a dry cabin only.
Mounting
When fitting ensure that the ventilation slots are not obstructed and take care not to over tighten the screws. When in operation the space behind the unit may get warm so avoid mounting on surfaces where this could cause a problem.
The power leads can be taken through a convenient hole in the mounting panel or alternatively through one of the end vent slots. Connect to a 12 volt DC supply via a suitable switch and a 1 Amp fuse. The red wire goes to the positive supply connection and the black wire to negative. (An internal diode protects the unit against supply reversal.)

20W Semi Flexible SOLAR PANEL
At just 3.5mm thin our weather proof panels are tough enough to withstand being stepped on when wearing soft soled shoes
A solar panel can provide a near maintenance free solution to keeping batteries charged when unattended. An occasional wipe with a damp cloth is all that is necessary to ensure the panel continues to trickle energy into the battery. Keeping the battery topped up will improve its reliability and can extend its useful working life. Whilst solar panels give their maximum output in direct sunlight, even an overcast day can provide a useful level of charge.
The Nasa Marine 12 volt, semi flexible solar panel is robustly constructed on a fibre glass substrate and are protected by a scratch proof transparent Tedlar polymer. Only 3.5mm thick and lightweight, they have no metal outer components to make contact with the surface to which they are fitted. The efficient and stable polycrystalline cells are encapsulated between two tough outer layers so the whole panel is weatherproof and carries a limited one year warranty.
The panel can be gently flexed (in one dimension.) to follow a smooth curve, such as a coach roof, by up to 2.5cm per 100cm of panel length. Four, grommet finished, holes are provided for screw fixing. Alternatively panels can be glued into position using mastic. The panels do not contain glass and, when correctly mounted, can be stepped upon when wearing soft soled shoes.
A sealed junction box is fitted with 2.5m of output cable, a connector and fuse protected crocodile clips. Electrical connection is simple though the use of a solar regulator is recommended to prevent overcharge if the system is to be left unattended for long periods or the solar panel to battery ratio exceeds the minimum of 10W to 100Ah. An internal blocking diode prevents reverse current drain at night. The panel is protected with an inline 3 Amp fuse.
The 20W panel measures 510 x 360mm