Tactical Wind Mast Sensor
A high performance system that sends NMEA wind speed and direction data 10 times a second.
In demanding conditions, where high performance is essential, the Clipper Tactical wind mast sensor is the ideal choice. With ten updates every second it responds very quickly to the changes in wind speed and direction, which occur during tricky manoeuvres. The sensor is supplied complete with a mast mounting kit, 20 metres of light weight cable and all necessary electrical connectors to complete the installation. The output data is in the NMEA 0183 format and can be used to drive any compatible display that utilises the MWV sentence.
NOTE – This 3 wire NMEA mast unit is not compatible with earlier 5 wire analogue Clipper, Target or Cruiser wind systems. The earlier analogue mast sensor is available on the spare parts page.
- Mast transmitter supplied with 20 metres of cable
- NMEA 0183 4800 Baud data sentence MWV – update rate = 10 per second
- Wind speed 0 to 99.9 Kts
- Wind direction 0 to 360 degrees
- Supply voltage nominal 12 Volts
- Wind sensor supply current 9mA
You may also like...
Supernova Combi Tri and Anchor L.E.D mastlight
Supernova lights use high efficiency LEDs ensuring long life and low power consumption. A tough polycarbonate shell protects Supernova from the elements while a Gore-Tex membrane vent ensures equalization of pressure on the seals.
A simple two wire connection powers the Combi light. Connecting the red wire to positive and the black wire to negative will illuminate the tricolour light. Reversing the connections will illuminate the anchor light.
A rotary switch is supplied with the Combi light to facilitate the supply reversal.
In the central position both lights are off. Switching clockwise or anticlockwise selects the required lighting configuration.
If a toggle or rocker switch is preferred, to match existing switches, then a centreoff two pole changeover switch can be used.
Supernova navigation lights are intended for use on vessels up to 12 metres in length. They comply with CE generic EMC standards and are waterproof to IP65 and IP67. There is no specific EU standard for LED navigation lights. Supernova lights do not have any national approvals.
A large display, mast mounted, multifunction repeater is now being produced at our factory. The weatherproof repeater with its 60mm high numerals, is supplied complete with cables, data-box with six NMEA-0183 inputs ( With up to six sentences per input.), wireless remote control, stainless steel mounting brackets and weather cover. There are nine levels of red back lighting which permit easy night viewing of red characters on a black background. The overall case size is 211mm wide x 140mm high.
Currently programmed in are the screens shown below though we do welcome customer feedback as we will add to this list by popular demand.
MOBi MOB Indicator
The Nasa MOBi is a state of the art, fail-safe transponder man overboard system. It consists of a base unit and up to eight active transponders for crew or valuable equipment. In operation the base station sequentially interrogates each transponder which then broadcasts its presence. In the event of a crew member falling overboard the drop in signal level is detected by the base unit which sounds a high intensity audible alarm. To aid identification of the missing crew member the base station continually displays the names of all the crew currently logged on, the signal levels of their transponder fob and their current status. Three AAA cells power each transponder for several weeks of continuous use. Should the base station be turned off the transponders will go to sleep with a life of several years. So if you are sailing with Tom, Dick and Harry don’t forget to take MOBi with you!
EASY LIGHT LED Luminaire
The NASA Marine 12 Volt Easylight luminaire contains 48 high efficiency LEDs in a slender surface mounting package.
The cool white version (CW) is recommended where maximum illumination is required and the warm white (WW) where a more natural light is preferred. Light output for the (CW) is typically 300 Lumens and typically 250 Lumens for the (WW).
The unit is designed for surface mounting directly on a ceiling or wall using the screws provided. It is not waterproof and is intended for use in a dry cabin only.
When fitting ensure that the ventilation slots are not obstructed and take care not to over tighten the screws. When in operation the space behind the unit may get warm so avoid mounting on surfaces where this could cause a problem.
The power leads can be taken through a convenient hole in the mounting panel or alternatively through one of the end vent slots. Connect to a 12 volt DC supply via a suitable switch and a 1 Amp fuse. The red wire goes to the positive supply connection and the black wire to negative. (An internal diode protects the unit against supply reversal.)
HF3W SSB Receiver
TARGET HF3/P & HF3/W
The Target HF3 is a masterpiece of R. F. engineering covering the entire spectrum between 30Khz to 30Mhz. For those new to single side band reception the unit comes complete with everything needed to ‘get on the air’ including a comprehensive instruction manual which includes a list of useful marine frequencies.
Controls on the front of the receiver change reception mode, from a narrow filter for SSB reception to a wide filter which enables high quality audio signals to be heard from broadcast stations around the world. They also control ten memory channels to store your favourite frequencies.
The large, clear liquid crystal display shows the precise frequency tuned to and there is no need for constant ‘correcting’ with the tuning knob so often associated with SSB signals as the receiver
is fully synthesised.
The Target HF3/P has a fixed level audio output to connect to third party weatherfax software. The receiver is supplied complete with a basic long wire antenna, 12 volt power cable and instruction book.
The HF3/W is complete with CD software and interface cable for connection to a PC sound card. The software enables reception of weatherfax pictures, Radiotelex weather forecasts and Navtex. Simply install the software, plug in the supplied cable to the receiver output and PC sound card to receive weatherfax pictures and forecasts from around the world.
Requires PC Windows XP to 7.
H Vector Navtex Antenna
Conventional navtex antennas respond to the electrical component associated with the navtex radio signal. They usually perform well at sea where electrical interference is low but can sometimes be overwhelmed with interference especially when in harbour and connected to shore power.
In most small craft the electrical system acts as an effective ground for the antenna but it can also be a source of interference conducted from other electrical equipment on board. Electrical interference can result in poor reception especially in a marina where the ambient level is high or at sea when poorly suppressed electrical equipment is in use.
The omnidirectional H-Vector antenna is not sensitive to electric fields but to the magnetic component of the navtex signal. As a result it is less sensitive to locally generated interference and, as it does not need a ground, it is not affected by conducted ground interference whether in harbour or at sea.
The net result is that, under adverse conditions, the H-Vector antenna can deliver a significant improvement to navtex reception. The mushroom shaped antenna is compatible with the Clipper navtex, series 2 Target navtex and with the navtex engine. It can be mounted on a cabin roof or rail mounted using an appropriate threaded antenna base.